top of page

About Us

 Founded in 2007, FRCABLE is a trailblazing company in the solar photovoltaic industry, specializing in the production of high-quality cables and cross-linked cables.

Are Solar Panel Connectors Waterproof? IP67 vs. IP68 Explained

4 days ago
11 min read

Are Solar Panel Connectors Waterproof?

Solar panel connectors are designed to withstand outdoor conditions, including rain, moisture, dust, and temperature changes. However, not every solar connector offers the same level of water protection.

When evaluating whether solar panel connectors are waterproof, two common ratings are IP67 and IP68. Both provide dust-tight protection, but they differ in their resistance to water immersion.

An IP67 connector is tested for temporary immersion under standardized conditions, while an IP68 connector is designed for continuous immersion under manufacturer-specified conditions.

However, there is an important detail that many buyers overlook: the waterproof rating of a solar connector often applies only when the male and female connectors are correctly assembled and fully mated.

A connector that is rated IP68 when connected may have a much lower protection rating when disconnected.

Understanding these differences helps solar installers, EPC contractors, and PV equipment buyers select suitable connectors and avoid water-related connection failures.


What Does Waterproof Mean for Solar Panel Connectors

1. What Does Waterproof Mean for Solar Panel Connectors?

A waterproof solar connector is designed to prevent water from entering its internal contact area under specified test conditions.

Most outdoor photovoltaic connectors use sealing components, such as rubber or silicone seals, to prevent moisture from reaching the electrical contacts.

A typical solar connector includes several components that contribute to its water protection:

  • Connector housing: Protects the internal electrical contacts from external environmental exposure.

  • Sealing ring: Creates a watertight seal between the male and female connector bodies.

  • Cable gland: Compresses around the cable jacket to prevent moisture from entering through the cable entry.

  • Locking mechanism: Keeps the connector fully engaged and maintains the intended sealing pressure.

  • Crimped contact: Provides a reliable electrical connection between the conductor and the connector terminal.

The overall protection depends on these components working together.

A high IP rating cannot compensate for a damaged sealing ring, incorrectly sized cable, poor assembly, or incomplete connection.

It is also important to understand that waterproof does not mean suitable for every underwater application. An IP rating describes resistance to water ingress under specific laboratory conditions, not unlimited protection against water exposure throughout the connector's entire service life.


What Do IP67 and IP68 Mean

2. What Do IP67 and IP68 Mean?

IP stands for Ingress Protection. The IP Code is defined by IEC 60529 and classifies the degree of protection provided by an enclosure against solid particles and water.

The code normally consists of two digits.

  • The first digit indicates protection against solid objects and dust.

  • The second digit indicates protection against water.

For example, both IP67 and IP68 begin with the number 6, meaning they provide dust-tight protection.

The difference is in the second digit.


What Does IP67 Mean?

IP67 means:

  • IP6: Completely dust-tight under the applicable test requirements.

  • IP7: Protected against the effects of temporary immersion in water under standardized test conditions.

Under IEC 60529, the IPX7 test involves a 30-minute immersion test. It is commonly summarized as immersion at a depth of 1 meter, although the precise immersion setup depends on the dimensions and position of the tested enclosure.

For solar applications, an IP67 connector provides a defined level of protection against temporary water immersion when used in the configuration covered by its test.

However, IP67 does not mean that a connector can remain underwater indefinitely.


What Does IP68 Mean?

IP68 also provides dust-tight protection but is designed for continuous immersion under specified conditions.

Unlike IP67, IP68 does not have one universal immersion depth or test duration that applies to every product.

The test conditions are agreed between the manufacturer and the user, taking into account the intended application. They must be more severe than the conditions specified for IP67.

For this reason, an IP68 marking alone does not tell buyers how deep or how long a connector can remain underwater.

Always check the product datasheet for the actual immersion conditions.

For example, one manufacturer may specify IP68 at 1 meter for 1 hour, while another product may have a different tested duration or depth.


IP67 vs. IP68: Key Differences

Parameter

IP67

IP68

Dust protection

Dust-tight

Dust-tight

Water protection

Temporary immersion

Continuous immersion under specified conditions

Immersion test

Standardized 30-minute test

Manufacturer-specified depth and duration

Test conditions

Standardized under IEC 60529

More severe than IPX7

Long-term underwater use

Not covered

Only within the specified product conditions

Water jet protection

Not automatically guaranteed

Not automatically guaranteed

One important point: IP68 does not automatically mean better protection against high-pressure water jets than IP67.

IEC 60529 treats water jet protection and immersion protection as different test categories. An enclosure marked only IPX7 or IPX8 is not automatically suitable for water jet exposure.

This is why some solar connector manufacturers specify both IP65 and IP68, indicating protection against the relevant water jet and immersion tests.



3. Are IP67 or IP68 Solar Connectors Better?

Neither rating is automatically the best choice for every photovoltaic installation.

The correct rating depends on the installation environment, connector design, and manufacturer's specifications.


When Is IP67 Suitable?

IP67 connectors may be suitable for outdoor electrical applications where temporary immersion protection is required.

For example:

  • Outdoor photovoltaic installations exposed to rain.

  • Solar cable connections installed beneath PV modules.

  • Electrical connections in environments where temporary water exposure may occur.

  • Applications where the manufacturer's IP67 rating meets the project requirements.

However, the actual installation must still follow the connector manufacturer's instructions.


When Is IP68 Worth Considering?

IP68 connectors may be worth considering when the application requires a higher level of protection against prolonged immersion.

Potential applications include:

  • Solar installations in locations with a higher risk of temporary flooding.

  • Equipment exposed to prolonged standing water.

  • PV electrical connections with specific immersion protection requirements.

  • Projects where the engineering specification explicitly requires IP68-rated components.

Even in these applications, IP68 should not be treated as permission to install connectors underwater without further evaluation.

The entire assembly, cable entry, installation arrangement, and operating conditions must be suitable for the intended exposure.

For most solar projects, selecting a correctly certified connector with a verified IP rating and proper installation is more important than simply choosing the highest IP number.


Are Solar Panel Connectors Waterproof? IP67 vs. IP68 Explained

4. Does the Waterproof Rating Apply When Solar Connectors Are Disconnected?

This is one of the most important details to check when purchasing photovoltaic connectors.

A solar connector may have different protection ratings depending on whether it is connected or disconnected.

Manufacturers commonly identify these conditions as:

  • Mated: The male and female connector parts are fully connected.

  • Unmated: The two connector parts are disconnected.

For example, Stäubli's Original MC4 product documentation specifies IP65/IP68 protection when mated, with an IP68 immersion condition of 1 meter for 1 hour. Its listed unmated protection is IP2X.

Amphenol also specifies IP68 protection at 1 meter for 1 hour when mated for its H4 connector, while listing IP2X for the unmated condition.

These examples demonstrate why checking the exact product datasheet is essential.

An IP2X designation does not indicate water protection. Therefore, a disconnected connector should never be assumed to retain its mated waterproof rating.


Why Does Mating Condition Matter?

When two compatible connector halves are fully assembled, their sealing surfaces work together to prevent moisture from entering the contact area.

If the connector is disconnected:

  • The sealing interface is exposed.

  • Dust and moisture can reach internal surfaces.

  • Water can accumulate around exposed electrical contacts.

  • Dirt or corrosion may affect the next connection.

If a connector must remain unused, use the manufacturer's designated protective sealing caps where specified.

Do not rely on the connector's mated IP rating to protect an exposed connector end.



5. Why Can IP68 Solar Connectors Still Leak Water?

An IP68 marking does not guarantee that every installed connector will remain waterproof under all operating conditions.

In actual PV installations, water ingress can occur because of incorrect assembly, mechanical damage, or incompatible connector components.

Here are some common causes.


1. Incomplete Connector Mating

Solar connectors must be fully inserted and locked according to the manufacturer's instructions.

A partially connected pair may leave a gap between the connector bodies.

This can compromise the sealing interface and allow moisture from rain, wind-driven water, or accumulated snow to enter.

Always check that the locking mechanism is properly engaged.


2. Incorrect Cable Diameter

The cable gland is designed to seal around a specific range of cable outside diameters.

If the solar cable is too small, the sealing component may not compress sufficiently.

If the cable is too large, the gland may become difficult to assemble or may not seal correctly.

Before purchasing a connector, check:

  • Compatible cable cross-sectional area.

  • Permitted cable outside diameter.

  • Cable insulation construction.

  • Connector manufacturer's approved cable specifications.

Matching the cable to the connector's specifications is essential for maintaining the intended sealing performance.


3. Damaged or Incorrectly Installed Sealing Components

A sealing ring can lose its effectiveness if it is:

  • Cut or scratched during assembly.

  • Contaminated with dust or debris.

  • Twisted or incorrectly positioned.

  • Deformed through excessive tightening.

  • Damaged by incompatible chemicals or lubricants.

Inspect sealing components before assembly and follow the manufacturer's specified installation procedure.

Do not add silicone sealant or other materials unless the connector manufacturer explicitly permits them.


4. Improper Crimping and Assembly

A photovoltaic connector requires more than a waterproof housing.

The metal contact must be correctly crimped to the conductor using the specified contact and crimping tool.

Incorrect crimping can cause increased contact resistance, localized heating, and electrical failure.

Improper assembly can also compromise the cable entry seal.

For this reason, connector assembly should follow the manufacturer's approved stripping, crimping, insertion, and tightening procedures.


5. Mixing Connectors From Different Manufacturers

Two solar connectors may look almost identical and appear to fit together.

However, physical compatibility does not necessarily mean that the combination has been tested or approved.

Different manufacturers may use different:

  • Contact dimensions.

  • Locking mechanisms.

  • Sealing structures.

  • Contact materials.

  • Cable gland designs.

  • Manufacturing tolerances.

Mixing incompatible connectors can compromise both electrical performance and water protection.

UL 6703 identifies connectors with their compatible mating parts. Connectors are generally expected to be used with compatible parts from the same brand unless intermatability has been specifically evaluated.

Always verify the approved mating combination instead of relying on descriptions such as "MC4 compatible."



6. How to Choose Waterproof Solar Panel Connectors

When purchasing solar connectors for a photovoltaic project, checking only the IP67 or IP68 marking is not enough.

Buyers should evaluate the complete technical specification.


Check the Exact IP Rating

Request the official datasheet for the specific connector model.

Confirm whether the rating is:

  • IP67.

  • IP68.

  • IP65/IP68.

  • Another tested protection combination.

Do not assume that every connector in the same product family has identical protection performance.


Check the Mated and Unmated Protection Levels

Look for separate specifications for connected and disconnected conditions.

A reliable datasheet should clearly identify whether the IP rating applies to the fully mated connector assembly.

Also check whether protective caps are available for unused connector ends.


Verify Immersion Depth and Duration

For IP68 products, request the actual test conditions.

Ask the manufacturer:

  • What is the maximum tested immersion depth?

  • How long was the immersion test conducted?

  • Was the connector tested in its fully mated configuration?

  • Which standard or test procedure was followed?

An IP68 label without supporting test conditions provides limited information for comparing products.


Verify PV Connector Certification

For photovoltaic applications, buyers should also check the applicable connector product standards.

Common examples include:

  • IEC 62852 for photovoltaic connectors.

  • UL 6703 for connectors used in photovoltaic systems in applicable North American markets.

An IP rating and a PV connector certification serve different purposes.

IP ratings describe ingress protection, while PV connector standards address requirements associated with photovoltaic electrical connectors.

Neither should be used as a substitute for checking the other.


Check Electrical and Environmental Specifications

Water protection is only one part of connector performance.

Also evaluate:

Parameter

What Buyers Should Check

Rated voltage

Compatibility with the PV system DC voltage

Rated current

Suitable for the maximum operating current

Cable size

Compatible conductor cross-section

Cable outside diameter

Compatible with the sealing gland

Contact material

Suitable conductive material and plating

Operating temperature

Suitable for the installation environment

UV resistance

Suitable for long-term outdoor exposure

Salt mist resistance

Important for coastal and marine environments

Mating cycles

Mechanical durability during connection and disconnection

A connector may have an excellent IP rating but still be unsuitable for a particular PV installation if its current rating, cable compatibility, temperature range, or certification is incorrect.



7. How to Maintain the Waterproof Performance of Solar Connectors

Correct product selection is only the first step. Proper installation and maintenance are equally important.

Follow these basic practices to reduce the risk of moisture-related failures.

1. Use compatible connector pairs.

Use connector halves approved by the same manufacturer and for the same product family, unless a specific cross-manufacturer combination has been formally evaluated and approved.

2. Use the correct solar cable.

Verify the cable cross-sectional area and outside diameter against the connector datasheet.

3. Inspect sealing components before assembly.

Make sure the sealing ring and cable gland are clean, correctly positioned, and free from damage.

4. Use the specified crimping tools.

Incorrect crimping can result in poor electrical contact and increased resistance.

5. Fully engage the locking mechanism.

Push the connector halves together until the manufacturer's specified locking engagement is achieved. Confirm proper seating through visual inspection.

6. Keep connectors away from standing water.

Secure cables and connectors beneath the modules or in other manufacturer-approved positions. Avoid leaving connectors directly on wet roof surfaces or where water can accumulate.

7. Inspect connectors periodically.

Look for cracked housings, damaged seals, corrosion, discoloration, loose connections, and signs of overheating.

Damaged connectors should be replaced using approved compatible components.

PV connector inspection, replacement, and disconnection should be performed by qualified personnel following the required electrical safety procedures. Never disconnect a PV connector under load.



8. Do You Really Need IP68 Solar Connectors?

Not necessarily.

IP68 offers a higher level of protection against immersion under the specified conditions, but that does not automatically make it the right choice for every solar installation.

For many conventional rooftop PV systems, the actual requirements are reliable outdoor protection, correct electrical ratings, long-term environmental resistance, and proper installation.

For installations exposed to prolonged standing water or potential immersion, IP68 may be an important specification.

However, a higher IP rating cannot solve problems such as:

  • Incorrect connector compatibility.

  • Damaged sealing rings.

  • Poor cable crimping.

  • Improper cable sizing.

  • Incomplete connector mating.

  • Incorrect installation locations.

A well-designed and properly installed IP67 connector can be a better choice for a particular application than an incorrectly selected or assembled IP68 connector.

The most reliable approach is to evaluate the connector's complete technical documentation and match its protection capabilities to the actual installation environment.



Frequently Asked Questions


Are solar panel connectors waterproof in the rain?

Yes, many solar panel connectors are designed for outdoor use and provide protection against rain and moisture when correctly assembled. However, the actual protection depends on the connector's IP rating, mating condition, and installation quality.


Can IP67 solar connectors be submerged in water?

IP67 connectors are tested against temporary water immersion under standardized conditions, commonly described as 1 meter for 30 minutes. This does not mean they are designed for permanent underwater installation.


Is IP68 better than IP67 for solar connectors?

IP68 provides protection against continuous immersion under manufacturer-specified conditions, which must be more severe than the IPX7 test. However, it does not automatically provide better protection against high-pressure water jets. Check the complete IP rating and test conditions.


Are MC4 connectors waterproof when disconnected?

Not necessarily. Some original MC4 products have IP65/IP68 protection when mated but only IP2X protection when unmated. Always check the specifications of the exact connector model and use the designated protective caps where required.


Can different brands of MC4 connectors be connected together?

Physical fit does not establish certified compatibility. Different connector manufacturers may use different contact designs, sealing structures, and mechanical tolerances. Use compatible connector pairs approved by the manufacturer.

Does IP68 mean a solar connector can stay underwater permanently?

No. IP68 protection applies under specific tested immersion conditions. The exact depth and duration must be confirmed in the manufacturer's technical documentation. It should not be interpreted as unlimited underwater protection.



What causes water to enter an IP68 solar connector?

Common causes include incomplete mating, damaged sealing rings, incorrect cable diameter, improper assembly, and incompatible connector combinations. An IP68 rating does not eliminate the need for correct installation and inspection.



Final Thoughts

Solar panel connectors are designed to operate in demanding outdoor environments, but their waterproof performance depends on more than the IP rating printed on the housing.

IP67 and IP68 describe different levels of protection against water immersion. Understanding their test conditions, checking whether the rating applies to mated or unmated connectors, and verifying the correct connector combination are all essential when selecting PV components.

For solar installers, EPC contractors, and equipment buyers, the best connector is not simply the one with the highest IP rating. It is the one with verified protection performance, appropriate electrical specifications, compatible mating components, and reliable installation requirements.

Comments


whatsapp-icon
bottom of page